Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Don't underestimate the forklift at work. If the procedure is not good, there will certainly be serious accidents in mins, and there are several mishaps entailing forklifts.

Situation 1: The forklift cargo obstructed the vehicle driver's view, and the individual in front can not be found, causing a moving crash.
Case 2: In order to preserve the equilibrium of the forklift when lifting heavy items, the employees utilized their body weight as the counterweight, which practically created casualties.
Case 3: The width of the forklift cargo goes beyond the permitted width of the course and holds on the roadside rack, which nearly creates an accident.
Case 4: Forklift is speeding and surrender during a turn.
Instance 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not notice the forklift.
Situation 6: The forklift raises the personnel illegally, the forklift vehicle driver does not use the safety belt, the forklift lifter drops and the driver is crushed when the forklift rolls over.
Situation 7: The forklift motorist did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift operation need to pay attention to these issues ：.

Begin.
1. Prior to starting, observe the surroundings, and after verifying that there are no obstacles that hinder the security of driving, honk the horn initially and after that start.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be secure prior to starting.
3. When the forklift starts with a tons, the chauffeur must initially verify that the load is stable and trustworthy.
4. The start needs to be slow and steady.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground need to be maintained 300mm-400mm, and the pole should be tilted backward. .
2. Do not raise the fork expensive when driving. When going into and leaving the work site or while driving, be careful that there will be no challenges in the sky. When the tons is taking a trip, the fork must not be increased expensive, which will certainly affect the security of the forklift. .
3. After discharging, the fork must be lowered to the regular driving placement prior to driving. .
4. When transforming, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are restricted. High-speed sharp turns will certainly create the vehicle to shed side stability and topple. .
5. When the forklift is downhill, it is purely restricted to turn off the fire and slide, and it is forbidden to brake instantly while driving with lots unless there are special circumstances.
6. When the forklift is running, it has to obey the web traffic rules in the factory and should keep a specific safety range from the vehicle in front. .
7. When the forklift is running, the tons has to be in the lowest placement that does not impede the driving, and the gantry ought to be correctly slanted back. The tons shall not be elevated other than when stacking or packing. .
8. The elevation of the lots should not block the driver's view. In unique scenarios, when the item influences the forward vision, drive at a low speed when turning around.
9. It is forbidden to switch on the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the factory area is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop location. .
11. When the forklift is lifted, raised or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing function. .
12. If troubles are found, they will certainly be repaired and reported in a timely way, and they will certainly never run with diseases or hide them.

packing and dumping.
1. When fork-loading items, the range in between the two forks need to be adjusted as required to make the tons of both forks balanced and not skewed, and one side of the item must be against the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or draw. In special conditions, safety indication have to be set up to advise surrounding pedestrians. .
3. In the process of filling and dumping items, the forklift must be stopped with the brake. .
4. The speed of the car should be slow-moving and constant. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled objects and injure individuals. .
5. When using a fork to fork the goods, the fork ought to be as deep as possible under the tons, and it must be noted that the fork suggestion must not touch various other products or objects. The load needs to be stabilized with very little back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the lots is reduced to allow for very easy positioning of the tons and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure people. .
8. Overloading is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude falling accidents. .
9. It is not allowed to utilize the brake inertia to slip, put, round or roll items. .
10. It is not enabled to make use of forks to select, transform pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, Stand-on Electric Pallet Stacker you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is removed. (Except for special scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look needs to be examined, and gas, lubing oil and cooling water should be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak must likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the auto;.
2. When you run into somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. Stand-on Electric Pallet Stacker When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be too sharp to stop the propensity of "free switching";.
6. Running up and down the slope needs to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into big or hefty goods and most likely to the driver's view, they should take the turning around workout
.
The "Eight Prohibitions" ought to be adhered to in the procedure.
1. Single fork operation is not enabled.
2. It is not permitted to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to exile round or easy-to-roll things.
7. It is not permitted to bring people to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844